Hill-Rom DuraStar Series Скачать руководство пользователя страница 26

Страница: 26 / 165

General Operation

Chapter 1: Introduction

DuraStar™ Series Stretcher Service Manual (man268)

Page 1 - 17

Trendelenburg/Reverse Trendelenburg Operation

The Trendelenburg/Reverse Trendelenburg pedals are located on both sides of
the hydraulic stretcher. The stretcher must be in a raised position to achieve
Trendelenburg/Reverse Trendelenburg positions.

Trendelenburg

Press the foot pedal marked with the graphic showing Trendelenburg until the
desired angle is reached.

Reverse Trendelenburg

Press the foot pedal marked with the graphic showing Reverse Trendelenburg
until the desired angle is reached.

Quick Trendelenburg

Grasp the permanent push handle located at the foot end, and pull up on the
stretcher until the desired angle is reached.

Leveling the Sleep Surface

• If the stretcher is in the Trendelenburg position, press the Reverse

Trendelenburg pedal until the stretcher is level.

• If the stretcher is in the Reverse Trendelenburg position, press the

Trendelenburg pedal until the stretcher is level.

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 26 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: