manualshive.com logo in svg

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 38 / 165

Поделиться
Скачать
Hill-Rom DuraStar Series Скачать руководство пользователя страница 38

DuraStar™ Hydraulic Stretcher Function Checks

Chapter 2: Troubleshooting Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 2 - 5

2

5. Put the stretcher in the neutral position. The pedal seats in that position, 

and all four casters rotate and roll freely.

Yes

No

↓

→

Go to RAP 2.3.

Hilow Function

6. Put a 40 lb (18 kg) weight on the stretcher. Press the right side pump pedal 

24 times to raise the stretcher to the high position. The stretcher rises 
evenly, and no more than 24 full pumps are required to reach the high 
position. 

Yes

No

↓

→

Go to RAP 2.4.

7. Press the center release pedal, and lower the stretcher. The head and foot 

ends of the stretcher lower evenly.

Yes

No

↓

→

Go to RAP 2.5.

8. Press the left side pump pedal 24 times to raise the stretcher to the high 

position. The stretcher rises evenly, and no more than 24 full pumps are 
required to reach the high position.

Yes

No

↓

→

Go to RAP 2.4.

9. Press the center release pedal, and lower the stretcher. The head and foot 

ends of the stretcher lower evenly.

Yes

No

↓

→

Go to RAP 2.5.

10. Remove the 40 lb (18 kg) weight, and continue to step 11.

Содержание DuraStar Series






































































































































































Отзывы:

Нет отзывов