Hill-Rom DuraStar Series Скачать руководство пользователя страница 49

Страница: 49 / 165

2.5 Stretcher Will Not Lower

Chapter 2: Troubleshooting Procedures

Page 2 - 16

DuraStar™ Series Stretcher Service Manual (man268)

2.5

Stretcher Will Not Lower

1. When the foot release pedal is pushed, the Trendelenburg offset plunger

(D) fully depresses the release pin (B) on the hydraulic cylinder (A) (see
figure 2-3 on page 2-16).

Figure 2-3. Release Mechanism Location

Yes

↓

→

Adjust the release mechanism (refer to procedure 4.10). If this
solves the problem, go to “Final Actions” on page 2-8.
Otherwise, go to step 2.

2. The wireforms (C) are bent or missing.

Yes

↓

→

Go to step 3.

3. Replace the bent or missing wireforms.

This solves the problem.

Yes

↓

→

Go to step 5.

4. Go to “Final Actions” on page 2-8.

m268_013

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 49 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: