Hill-Rom DuraStar Series Скачать руководство пользователя страница 91

Страница: 91 / 165

4.10 Hydraulic Cylinder Release

Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 34

DuraStar™ Series Stretcher Service Manual (man268)

4.10 Hydraulic Cylinder Release

Tools required:

Torque wrench 0-250 in-lb
1/8" Allen™

wrench

Adjustment

1. Push the corresponding release pedal down until the pedal stop comes in

contact with the base frame.

2. Slide the plunger (A) until the cylinder release pin (C) is fully depressed,

and the plunger (A) is flush with the cylinder (see figure 4-16 on page
4-34).

Figure 4-16. Release Pedals

3. Ensure the plunger (A) is centered on the cylinder release pin (C).

4. Using the 1/8" Allen™ wrench, tighten the screw (B) that holds the plunger

in place.

1. Allen™ is a trademark of Industrial Fasteners, Inc.

m268_044

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 91 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: