Hill-Rom DuraStar Series Скачать руководство пользователя страница 68

Страница: 68 / 165

4.3 Stretcher Back Panel Gas Spring

Chapter 4: Removal, Replacement, and Adjustment Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 4 - 11

5. Remove the retaining ring (F) and the headed pin (E) located at the bottom

of the spring.

6. Rotate the spring clockwise or counterclockwise to adjust.

7. Install the headed pin (E) and the retaining ring (F) located at the bottom of

the spring.

8. Check the operation of the release handle again, and repeat the adjustment

procedure if necessary.

9. Using a 17 mm wrench, tighten the jam nut (H).

10. To ensure proper operation of the DuraStar™ Hydraulic Stretcher, perform

the “DuraStar™ Hydraulic Stretcher Function Checks” on page 2-4. To
ensure proper operation of the DuraStar™ Fixed Height Stretcher, perform
the “DuraStar™ Fixed Height Stretcher Function Checks” on page 2-7.

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 68 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: