Hill-Rom DuraStar Series Скачать руководство пользователя страница 70

Страница: 70 / 165

4.4 DuraStar™ Hydraulic Stretcher Upper Frame

Chapter 4: Removal, Replacement, and Adjustment Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 4 - 13

WARNING:

Two people are required for this procedure. If you do not use two
people, personal injury could occur.

CAUTION:

Be careful not to damage the base shroud when you remove the upper
frame assembly.

3. As you lift the upper frame assembly, tap on the underside of the round

crosstube (C) with a rubber mallet/hammer until the frame separates from
the hydraulic cylinder shaft.

4. Lift the frame from the hydraulic cylinders.

Replacement

WARNING:

Two people are required for this procedure. If you do not use two
people, personal injury could occur.

CAUTION:

Be careful not to damage the base shroud when you install the upper
frame assembly.

1. Lift the upper frame, and put the round crosstube (C) of the upper frame

onto the hydraulic cylinders.

2. Ensure the frame is in position on both cylinders.

3. Using the ratchet and the 9/16" socket, install the washer (D), lockwasher

(B), and bolt (A) to secure the upper frame to the hydraulic cylinder.

4. Using the torque wrench, torque the bolt (A) to 125 + 19 in-lb (14.1 + 2.1

N·m).

5. To ensure proper operation, verify that the frame is in position and secured

on both cylinders.

6. To ensure proper operation of the DuraStar™ Hydraulic Stretcher, perform

the “DuraStar™ Hydraulic Stretcher Function Checks” on page 2-4.

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 70 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: