manualshive.com logo in svg

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 22 / 165

Поделиться
Скачать
Hill-Rom DuraStar Series Скачать руководство пользователя страница 22

Specifications

Chapter 1: Introduction

DuraStar™ Series Stretcher Service Manual (man268)

Page 1 - 13

1

Stretcher Back Section Inclination

Both models of the DuraStar™ Series Stretcher are mechanized so that the 
attendant can raise or lower the back section by squeezing the release handle 
located under the back section. The back section can be elevated from 0° to 
90°.

Hilow

The hydraulic stretcher is mechanized so that the attendant can raise or lower 
the sleep surface by pressing the appropriate pedals located on either side of 
the stretcher. The stretcher is equipped with two hydraulic cylinders to ensure 
that the stretcher lowers evenly with uneven loads.

Brake/Steer

Both stretcher models are mechanized so that the attendant can set the brake, 
steer, or put the stretcher in the neutral position from anywhere around the 
stretcher. The pedals are color-coded to enable quick use. All four casters 
provide braking for the stretcher.

Trendelenburg/Reverse Trendelenburg

The hydraulic stretcher is mechanized to achieve the Trendelenburg/Reverse 
Trendelenburg positions by pressing the proper foot pedals located on either 
side of the stretcher. Quick Trendelenburg can be achieved by grasping the 
foot end of the stretcher and pulling up. A maximum of 18° 
Trendelenburg/Reverse Trendelenburg can be achieved with the stretcher 
raised to the high position.

Siderails

Both stretcher models are equipped with 3/4 length siderails. They can be 
moved from the stored position to the upright position in one motion.

The siderails should always be in a full upright position and latched when a 
patient is unattended. When the siderails are raised, an audible click indicates 
that they are completely raised and locked in place.

Siderails are intended to be a reminder, not a patient retaining device. 
Appropriate medical personnel should determine the level of restraint 
necessary to ensure a patient remains safely in bed. Consult the security strap 
manufacturer’s instruction for use to verify the correct application of each 
security device.

Содержание DuraStar Series






































































































































































Отзывы:

Нет отзывов