Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 91

Страница: 91 / 220

4.8 Breaker Switches

Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 28

CarePorter™ Cart Service Manual (man239)

Figure 4-10. Breaker Switch Removal

8. Note the color, orientation, and location of the wires (D).

NOTE:
Note the orientation of the breakers to ensure proper positioning during the
replacement procedure.

9. Depress and squeeze the lock tabs (F) on both sides of the breaker switch

(E).

10. Push out and remove the breaker switch (E) from the base weldment (G).

Replacement

To install the replacement breaker switch (E), reverse the removal procedure.

Adjustment

No adjustment is required for the breaker switch (E).

m239_073

Содержание CarePorter P3000





























































































































































































































Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды