Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 86

Страница: 86 / 220

4.6 Duplex Receptacle

Chapter 4: Removal, Replacement, and Adjustment Procedures

CarePorter™ Cart Service Manual (man239)

Page 4 - 23

2. Using the screwdriver, tighten the terminal screws (G).

3. Push the duplex receptacle (D) into the opening in the device mount

weldment (E).

4. Using the phillips head screwdriver, install the two screws (C) that secure

the duplex receptacle (D) to the device mount weldment (E).

5. Cover the duplex receptacle faceplate (B).

6. Using the phillips head screwdriver, install the two screws (A) that secure

the duplex receptacle faceplate (B).

7. Test the duplex receptacle (D) for availability of power, and proper

grounding (refer to procedure 2.6).

Adjustment

No adjustment is required for the duplex receptacle (D).

Содержание CarePorter P3000





























































































































































































































Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды