Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 85

Страница: 85 / 220

4.6 Duplex Receptacle

Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 22

CarePorter™ Cart Service Manual (man239)

Figure 4-7. Duplex Receptacle Removal

6. Remove the duplex receptacle faceplate (B).

7. Using the phillips head screwdriver, remove the two screws (C) that secure

the duplex receptacle (D) to the device mount weldment (E).

8. Pull the duplex receptacle (D) out of the opening in the device mount

weldment (E).

9. Using the screwdriver, loosen the terminal screws (G) holding the color-

coded wires (F).

10. Note the color, orientation, and location of the color-coded wires (F).

11. Pull the wires out of the connection hole, and remove the color-coded wires

(F) from the terminals.

Replacement

1. Connect the color-coded wires (F) to their original terminals.

m239_046

Содержание CarePorter P3000





























































































































































































































Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды