Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 216

Страница: 216 / 220

7.7 Infusion Support System (ISS) Transfer Pole—P158

Chapter 7: Accessories

CarePorter™ Cart Service Manual (man239)

Page 7 - 17

Adjustment

1. To extend the upper portion of the ISS transfer pole (A), turn the black

collar (D) counterclockwise, and manually raise the upper section of the
pole.

2. Lock the pole in place by turning the black collar (D) clockwise until it

stops.

3. To lower the ISS transfer pole (A), grasp the upper section of the pole, turn

the black collar (D) counterclockwise, and manually lower the pole.

Removal

To remove the ISS transfer pole, reverse the installation procedure.

Содержание CarePorter P3000





























































































































































































































Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды