manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Hewlett Packard Enterprise ProLiant DL20 Gen10 Скачать руководство пользователя страница 85

CAUTION: To prevent damage to electrical components, take the appropriate anti-static precautions before
beginning any installation, removal, or replacement procedure. Improper grounding can cause electrostatic
discharge.

Prerequisites

Before you perform this procedure, make sure that you have a T-15 Torx screwdriver available.

Procedure

1.

If installed, 

remove the front bezel.

2.

Power down the server.

3.

Remove all power:

a. Disconnect each power cord from the power source.

b. Disconnect each power cord from the server.

4.

Disconnect all peripheral cables from the server.

5.

Remove the server from the rack.

6.

Remove the access panel.

7.

If installed, remove the processor air baffle.

8.

Remove the M.2 air guider.

9.

Allow the heatsink to cool.

10. Remove the heatsink:

a. Loosen one pair of diagonally opposite screws halfway, then loosen the other pair of screws.

b. Completely loosen all screws in the same sequence.

c. Remove the heatsink from the processor backplate.

Removal and replacement procedures

85

Содержание ProLiant DL20 Gen10


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды