manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Hewlett Packard Enterprise ProLiant DL20 Gen10 Скачать руководство пользователя страница 54

Procedure

1. If installed, remove the front bezel.

2. Power down the server.

3. Remove all power:

a. Disconnect each power cord from the power source.

b. Disconnect each power cord from the server.

4. Disconnect all peripheral cables from the server.

5. Remove the server from the rack.

6. Remove the access panel.

7. Remove the media bay blank:

a. Remove the screws securing the media bay blank.

Retain the screws for future use.

b. Disengage the media bay blank.

c. Remove the media bay blank.

To replace the component, reverse the removal procedure.

Removing and replacing the two-bay LFF drive backplane

Prerequisites

Before you perform this procedure, make sure that you have the following tools available:

• T-10 Torx screwdriver

• T-15 Torx screwdriver

Removal and replacement procedures

54

Содержание ProLiant DL20 Gen10


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды