manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Hewlett Packard Enterprise ProLiant DL20 Gen10 Скачать руководство пользователя страница 116

Front panel LEDs and buttons

Item

Description

Status

Definition

1

Health LED

1

Solid green

Normal

Flashing green

iLO is rebooting

Flashing amber

System degraded

2

Flashing red

System critical

2

2

NIC status LED

1

Solid green

Linked to network

Flashing green

Network active

Off

No network activity

3

Power On/Standby
button and system
power LED

1

Solid green

System on

Flashing green

Performing power-on sequence

Solid amber

System in standby

Off

No power present

3

4

UID button/LED

1

Solid blue

Activated

Flashing blue

• 1 flash per second = Remote management or

firmware upgrade in progress

• 4 flashes per second = iLO manual reboot sequence

initiated

• 8 flashes per second = iLO manual reboot sequence

in progress

Off

Deactivated

1 

When the LEDs described in this table flash simultaneously, a power fault has occurred. For more information, see 

Front panel LED

power fault codes.

2 

If the health LED indicates a degraded or critical state, review the system IML or use iLO to review the system health status.

3 

Facility power is not present, power cord is not attached, no power supplies are installed, or power supply failure has occurred.

Component identification

116

Содержание ProLiant DL20 Gen10


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды