manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Hewlett Packard Enterprise ProLiant DL20 Gen10 Скачать руководство пользователя страница 102

6.

Install the processor:

a. Hold the processor by the edges and align the:

• Socket notches with the processor notches

• Pin 1 indicator on the processor and the socket

b. Lower the processor straight down, without tilting or sliding the processor in the socket .

Make sure that the processor is properly seated in the socket.

CAUTION: The processor load plate and locking lever should close without resistance. Forcing to close these parts
can damage the processor and the socket. This damage might require replacing the system board.

7.

Close the processor load plate (callout 1), and then engage the processor locking lever (callout 2).

Removal and replacement procedures

102

Содержание ProLiant DL20 Gen10


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды