manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Hewlett Packard Enterprise ProLiant DL20 Gen10 Скачать руководство пользователя страница 104

12. Install all the components removed from the failed system board.

13. Install the M.2 air guider.

14. If removed, install the processor air baffle.

15. Install the access panel.

16. Install the front bezel.

17. Install the server into the rack.

18. Connect all peripheral cables to the server.

19. Connect the power cords:

a. Connect each power cord to the server.

b. Connect each power cord to the power source.

20. Power up the server.

21. If removed, install the front bezel.

22. Ensure all firmware, including option cards and embedded devices, is updated to the same versions to ensure that

the latest drivers are being used.

23. Re-enter any Secure Boot Keys that were previously added in the Secure Boot configuration.

24. Re-enter the server serial number and the product ID.

Re-entering the server serial number and product ID

After you replace the system board, the server serial number and the product ID must be configured:

Procedure

1. Access System Utilities. During POST, press F9.

2. On the System Utilities home screen, select System Configuration > BIOS/Platform Configuration (RBSU) >

Advanced Options > Advanced Service Options.

Removal and replacement procedures

104

Содержание ProLiant DL20 Gen10


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды