manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Hewlett Packard Enterprise ProLiant DL20 Gen10 Скачать руководство пользователя страница 57

To replace the component, reverse the removal procedures.

Removing and replacing the four-bay SFF drive backplane

Prerequisites

Before you perform this procedure, make sure that you have the following tools available:

• T-10 Torx screwdriver

• T-15 Torx screwdriver

Procedure

1.

If installed, 

remove the front bezel.

2.

Power down the server.

3.

Remove all power:

a. Disconnect each power cord from the power source.

b. Disconnect each power cord from the server.

4.

Disconnect all peripheral cables from the server.

5.

Remove the server from the rack.

6.

Remove the inner left rail attached to the chassis.

7.

Remove the access panel.

8.

Remove the front bezel.

Removal and replacement procedures

57

Содержание ProLiant DL20 Gen10


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды