manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Hewlett Packard Enterprise ProLiant DL20 Gen10 Скачать руководство пользователя страница 106

a. Disconnect each power cord from the power source.

b. Disconnect each power cord from the server.

4.

Disconnect all peripheral cables from the server.

5.

Remove the server from the rack.

6.

Remove the access panel.

7.

Locate the battery.

8.

Remove the system battery:

a. Use a small flat-bladed, nonconductive tool to press the battery latch (callout 1).

b. Remove the system battery from the socket (callout 2).

9.

Install the system battery:

a. With the side of the battery showing the "+" sign facing up, insert the battery into the socket (callout 1).

b. Press the system battery down until it clicks into place (callout 2).

10. Install the access panel.

11. Install the server into the rack.

Removal and replacement procedures

106

Содержание ProLiant DL20 Gen10


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды