manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Hewlett Packard Enterprise ProLiant DL20 Gen10 Скачать руководство пользователя страница 61

Prerequisites

Before you perform this procedure, make sure that you have the following tools available:

• T-10 Torx screwdriver

• T-15 Torx screwdriver

Procedure

1.

If installed, 

remove the front bezel.

2.

Power down the server.

3.

Remove all power:

a. Disconnect each power cord from the power source.

b. Disconnect each power cord from the server.

4.

Disconnect all peripheral cables from the server.

5.

Remove the server from the rack.

6.

Remove the access panel.

7.

Disconnect all cables connected to existing expansion board.

8.

Remove the riser cage.

9.

Remove the expansion board installed in slot 2 of the riser cage.

10. Remove the expansion board installed in slot 1 of the riser cage.

To replace the component, reverse the removal procedures.

Removal and replacement procedures

61

Содержание ProLiant DL20 Gen10


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды