HEIDELBERG Speedmaster CD 102, Руководство пользователя

Страница: 168 / 170

Index
E.2
Grease lubrication hole, D.1.9
Grease spray, D.1.9
Guide rail limit switch
Place of installation, D.3.13
Guide rail of the pile support plate
Limit switch, D.3.13
H
HOTEMP 2000
Lubricant of the central grease lubrication, D.1.10
I
Inner carrier air blowers
Adjusting the blast air, C.1.28
Ionizing unit
Adjusting the ion blower, C.1.34
Switching on, C.1.33
L
Lateral sheet separation blowers
Automatic adjustment, C.1.35
Manual adjustment, C.1.36
Setting the blast air volume, C.1.36
Legend
Maintenance schedule, D.1.6
Lifting suckers, C.1.20, D.3.5
Adjusting the lifting suckers, C.1.20
Cleaning and checking, D.3.5
Replacing lifting suckers, C.1.20
Limit switch
Guide rail of the pile support plate, D.3.13
Lubricant spray, D.1.9, D.1.10
Lubricant tube,
D.1.9
Lubricants
Approved lubricants,
D.1.10
Lubricating devices
Grease gun, D.1.9
Oil can, D.1.9
Oil gun, D.1.9
Oil spray, grease spray or lubricant spray, D.1.9
Lubricating oil, D.1.10
Mobil MOBILGEAR 629, D.1.10
Lubricating points
Ball type lubricating nipple, D.1.9
Grease lubrication hole, D.1.9
Oil lubrication hole, D.1.9
Recessed grease nipple, D.1.9
M
Maintenance
General maintenance information, D.1.3
How to use this manual, D.1.3
Maintenance reduces costs, D.1.3
Maintenance interval
15 000 000 impressions, or twice a year (green),
D.1.7
150 000 impressions, or daily (red),
D.1.7
3 000 000 impressions, or monthly (blue), D.1.7
30 000 000 impressions, or once a year (violet),
D.1.7
750 000 impressions, or weekly (yellow),
D.1.7
Maintenance schedule
General information, D.1.6
Legend, D.1.6
Middle bearing of the forwarding roller shaft, D.3.16
Place of installation, D.3.16
O
Oil can, D.1.9
Oil gun, D.1.9
Oil lubrication hole, D.1.9
Oil spray, D.1.9, D.1.10
Outer carrier air blowers
Adjusting the blast air,
C.1.29
Adjusting the direction of blast air,
C.1.29
Adjusting the height,
C.1.29
Overview table – suction head settings,
C.1.22
Lifting suckers and forwarding suckers, C.1.22
Sheet stops and forwarding flap, C.1.24
Overview table - suction head settings
Sheet separator fingers and sheet separation
blowers,
C.1.23
P
Peripheral units
Maintenance instructions,
D.1.5
Pile alignment
Adjusting spindle,
D.3.11
Pile alignment adjusting spindle
Maintenance point description, D.3.11
Place of installation, D.3.11
Pile change, C.1.3
Non-stop pile change, C.1.5
Normal pile change, C.1.3
Preloading device, C.1.9
Pile height sensor
Malfunctions, B.1.12
Switching on/off, B.1.2
Pile stops, C.1.31
Normal position, C.1.32
Setting for very thin printing materials, C.1.32
Preloading and pile change, C.1.9
Preloading device
Place of installation,
D.3.4