HCT epc Скачать руководство пользователя страница 8

Страница: 8 / 41

023-00354-Rev1.4 evc/epc

User

Manual

evc/epc

Controller

With

SAE

J1939

Interface

Using the evc/epc with your PC

Install the

raphical

ser

nterface (GUI) in a host PC. Use the default file locations for easy future

update. The user has the option to choose where the program should be located.

Don’t run the GUI from a network as it needs access to certain files only in the Windows directories.

System Requirements

Windows XP, Vista or Windows7, 100MB or greater free disk space.



Insert the CD into the PC drive and follow the on-screen instructions. This will install the evc/epc GUI,

manual and help files.



Install the Com Port drivers for the evc/epc.

Start



HCT Products



Digital Controllers



evc/epc



USB Serial Drivers, CDM

xxxxx

_setup.exe



To insure a complete install, run the CDM

xxxxx

twice.

The evc/epc can be powered by +5V USB to allow configuration without connecting to a 12/24V

system.

A message “Supply Voltage is Low” appears on the screen.

You may fully communicate, change, and

save settings to the unit. You can not drive the coil(s).

Содержание epc










































Результаты поиска

Содержание epc

Отзывы:

HCT epc, Руководство пользователя, Страница: 8 / 41

Результаты поиска

Содержание epc

Отзывы: