manualshive.com logo in svg

HCT epc, Руководство пользователя, Страница: 17 / 41

Поделиться
Скачать
HCT epc Скачать руководство пользователя страница 17

 

 

023-00354-Rev1.4      evc/epc 

User 

Manual 

    

 

Copyright © High Country Tek, Inc. – 2013 

 

17

 

evc/epc

 

Controller

  

With

 

SAE

 

J1939

 

Interface

 

Coil A/B Max

 

Current

 (0 to 3Amps) 

  When Current Feedback is “

ON

”, it determines the max current. 

 

 

When Current Feedback is “

OFF

”, the Coil A/B Min Current setting does not apply and is grayed out. The 

Max Current is used as a reference for the evc/epc to declare a coil short condition

 

when the output 

current is 

0.5A higher

 than the max setting.

 

 

 

 

 

 

The output PWM duty cycle 
matches the percent of demand.  

The current will change when 
supply voltage and/or coil 
temperature changes. 

The evc/epc does not declare an 
error because the output current 
1.16A is 

not

 

0.5A higher

 than the 

max setting 0.7A.

 

 

 

 

The evc/epc will declare an error 
because the output current 1.16A is 

0.5A higher

 than the max setting 

0.63A.

 

 

 

Ramp Up

 (.001 to 65.000 Seconds) – Determines the time for Output A or B to ramp 

UP

 from minimum to 

maximum current. 

Ramp Down

 (.001 to 65.000Seconds) – Determines the time for Output  A or B to ramp 

Down

 from 

maximum to minimum current. 

Coil A&B PWM Hz 

(33 to 500Hz) – This is the PWM or Dither frequency according to the valve spec. 

(Sun cartridges are 140Hz). 

 

 

 

Содержание epc










































Отзывы:

Нет отзывов