HCT epc Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 41

HCT epc Скачать руководство пользователя страница 10

023-00354-Rev1.4 evc/epc

User

Manual

Copyright © High Country Tek, Inc. – 2013

10

evc/epc

Controller

With

SAE

J1939

Interface

evc/epc GUI

File

All changes made through the GUI are temporary until saved permanently

.

Permanently save settings to unit:

Save the settings from the RAM (temporary) memory to the unit’s

EEPROM (permanent memory).

Permanently save settings to unit & file (.dat)

:

Permanently save the settings to the unit’s EEPROM

and to a data file that may be loaded later.

Settings will be lost if not permanently saved before power cycle.

Reset the unit with a power cycle, you must remove both the USB cable and DC power from the
unit.

Restore unit to last permanent settings saved:

Reload RAM with settings stored in the EEPROM. This

will undo all changes made since the last Permanent Save.

Restore unit settings from data file (.dat):

Load the data file from the PC to the evc/epc for different

modes of operation.

Restore unit from v1.03 data file:

Load the previous version data file from the PC to the evc/epc for

different modes of operation.

«
...
8
9
10
11
12
...
»

Содержание epc










































Отзывы:

Нет отзывов