HCT epc Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 41

HCT epc Скачать руководство пользователя страница 4

023-00354-Rev1.4 evc/epc

User

Manual

Copyright © High Country Tek, Inc. – 2013

4

evc/epc

Controller

With

SAE

J1939

Interface

Welcome

Welcome to the High Country Tek Inc. (HCT)

evc/epc

user manual.

If you have any questions, requesting new features or finding errors, please contact us @ 530-265-3236
or e-mail at

[email protected]

, giving details of the issues and your contact information.

Introduction

This manual explains the installation and use of the evc/epc Digital Controllers. Users need to understand
the hazards in an electromechanical environment. Read this entire manual before installation. Pay particular
attention to caution and safety information.

Cautions

Changing setup values or operating modes while the machine is running may cause unintended machine
movement. It may lead to possible

injury

or

death

. Any moving parts should be disabled prior to

changing setup values or operating modes. In any case, exercise caution and work should be completed
only by qualified personnel.

Warranty Information

High Country Tek guarantees this product to be free of defects in materials and workmanship for one year
from the date shipped from the factory. Within this time frame, High Country Tek will provide evaluation of
warranted items free of charge. Warranty repair or replacement will be at the factory’s discretion.

Please have the units full Model / Part Number and Serial Number available when contacting the factory.
Do not return products to the factory without a RMA (Return Material Authorization) number.

Controller Updates

HCT continuously improves the controllers and makes additional information and/or features available.
Please check on-line at

www.hctcontrols.com

for the latest products, software update and information.

«
...
2
3
4
5
6
...
»

Содержание epc










































Отзывы:

Нет отзывов