manualshive.com logo in svg

HCT epc, Руководство пользователя, Страница: 29 / 41

Поделиться
Скачать
HCT epc Скачать руководство пользователя страница 29

 

 

023-00354-Rev1.4      evc/epc 

User 

Manual 

    

 

Copyright © High Country Tek, Inc. – 2013 

 

29

 

evc/epc

 

Controller

  

With

 

SAE

 

J1939

 

Interface

Fixed

 

Set-point

RPM

RPM

 

Stop

1500rpm

RPM

 

Slow

1800rpm

Coil

 

A

0

 

Current

 

  When “Auto-Reverse” is “

OFF

”, Coil A current stays 0 until the RPM increases to above “RPM Stop”, it 

will increase proportionally to the measured RPM. 

 

 
 

 

 

 

 

 

  When “Auto-Reverse” is “

ON

”, Coil A current stays at 0 and Coil B current will ramp up to the Reverse 

Set-point. 

  After the reverse cycle is over, if the measured RPM increases to above RPM Stop, Coil A current 

increases proportionally. If not, the evc/epc will try Reverse Retry Count times, each time remaining in 
reverse for reverse time.  

  If the Reverse Retry Count is depleted and the measured RPM remains below RPM Stop, the evc/epc 

will declare an error. 

 

  At start-up the measured RPM must initially reach the “RPM Slow” to allow the evc/epc to ramp up Coil 

A. This ensures that the prime mover has started and is at a stable speed

.

 

 

Coil

 

B

RPM

 

Slow

(1800rpm)

Reverse

 

Set-point

RPM

 

Stop

(1500rpm)

Fixed

 

Set-point

Coil

 

A

Содержание epc










































Отзывы:

Нет отзывов