HCT epc Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 41

HCT epc Скачать руководство пользователя страница 22

023-00354-Rev1.4 evc/epc

User

Manual

Copyright © High Country Tek, Inc. – 2013

22

evc/epc

Controller

With

SAE

J1939

Interface

Pot Maximum



It sets the max command input. This demands 100% output.



If the command input is > POT M the Command Margin, the evc/epc will declare an error and

the outputs go to the default settings.

Pot Center

– Sets the value of the center of the deadband.

Pot Minimum



It sets the min command value. This demands 0% output.



If the command input is < POT Minimum - the Command Margin, the evc/epc will declare an error and

the outputs go to the default settings.

Reference voltage

is 5V @ 250mA.

HCT has a manual command potentiometer – part number 999-10205 that o0.5V

dc

to +4.5V

dc

when connected to a +5V

dc

user voltage.

Auto Calibrate Pot Input



Calibrate the command limits – i.e. joystick or foot pedal etc.



When the button is clicked, a box will appear with

instructions.



Adjust the input from full High to full Low, then adjust to the

neutral or crossover point.



“OK” to save the values.

«
...
20
21
22
23
24
...
»

Содержание epc










































Отзывы:

Нет отзывов