HCT epc Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 41

HCT epc Скачать руководство пользователя страница 15

023-00354-Rev1.4 evc/epc

User

Manual

Copyright © High Country Tek, Inc. – 2013

15

evc/epc

Controller

With

SAE

J1939

Interface

Dashboard

PWM% A/B

– displays the output for coil A

and B in the percent of duty cycle. The PWM% B
will be “Grayed Out” when Coil B is disabled.

% Demand A/B

–

displays the percent of

demand for the output with respect to the
Maximum and Minimum Current settings. The %
Demand B will be “Grayed Out” when Coil B is
disabled.

Coil Current A/B

– displays the output

current. The Coil B Current will be “Grayed Out”
when Coil B is disabled.

Enabled/Disabled

– displays the current state of the enable input connection.

Command Volts/mAmps

– Displays the voltage or current at the Command input - (pin 3).

Reference Volts

– Displays the voltage at the User Reference output - (pin 2).

Supply Volts

– Displays the voltage at the main Power Supply Input - (pin 1).

Average Coil Current

– Applies averaging function to the displayed coil current.

A

A

C

D

D

C

B

B

E

E

F

F

G

G

«
...
13
14
15
16
17
...
»

Содержание epc










































Отзывы:

Нет отзывов