Hainbuch HYDROK Скачать руководство пользователя

Страница: 22 / 112

HYDROK
Safety

Order h49 7144.907-333

2.8 Functionality

WARNING

Serious injuries caused by severe contamination
of the product!



Always comply with the cleaning instructions and
intervals [see »Cleaning« chapter].

2.9 Environmental protection

NOTE

Substantial damage to the environment can result
from non-compliant handling or incorrect dis-
posal of environmentally hazardous substances!



If environmentally hazardous substances enter
the environment accidentally, take immediate re-
medial action.



If in doubt, notify the relevant municipal authori-
ties about the incident.

The following environmentally hazardous substances are
used:

Lubricants, auxiliary materials and operating fluids

Lubricants such as grease and oil can contain toxic sub-
stances. These must not enter the environment.

Dispose of environmentally hazardous substances properly
[see »Disposal« chapter].

Содержание HYDROK

















































































































Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды

Hainbuch HYDROK, Руководство по эксплуатации

Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды