Hainbuch HYDROK Скачать руководство пользователя

Страница: 99 / 112

HYDROK
Maintenance

Order h49 7144.907-333

WARNING

Eye injuries and cuts caused by failure to wear
protective clothing during cleaning operation!



Never use compressed air to clean the product.



Also wear the following items of personal protec-
tive equipment, in addition to the basic equip-
ment:

NOTE

Damage to seals caused by the wrong solvent!



To clean the product, never use a solvent that at-
tacks and damages the sealing elements in-
stalled. Those installed sealing elements can be
made of NBR, Viton and PUR materials.



To clean the product, never use a solvent that
contains ester, nor a polar solvent.

NOTE

Damage to materials caused by incorrect installa-
tion of sealing elements!



Replace missing or damaged sealing elements.



Ensure that the sealing elements do not fall out or
get damaged during installation / removal, and
apply a thin coat of grease if necessary.

Cleanliness of the relevant limit stop and guide diameter are
essential for achieving axial and face run-out tolerances.

1. Remove the changing parts and the clamping element

from the product [see »Removal of changing parts« and
»Removal of clamping element« chapters].

2. Remove the product from the machine [see »Removal

of the product« chapter].

3. Drain all residue from the product.

Содержание HYDROK

















































































































Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды

Hainbuch HYDROK, Руководство по эксплуатации

Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды