Hainbuch HYDROK Скачать руководство пользователя

Страница: 24 / 112

HYDROK
Technical data

Order h49 7144.907-333

The achievable clamping forces resulting from actuating
forces must be checked at regular intervals. For this, struc-
tural clamping force measurements must be performed.

The clamping force measured must be in the approved range
[see »Clamping force diagram« chapter].

3.3 Balancing quality

The product is balanced before leaving the factory [balanc-
ing quality - see »General information« chapter].

DANGER

Serious injuries caused by parts being ejected
centrifugally if products are not balanced cor-
rectly!



Do not clamp rotationally symmetrical work-
pieces, or do so only after contacting the manu-
facturer.



Never remove balancing screws and weights at-
tached to the product.

NOTE

Material damage caused by machining with incor-
rectly balanced products!



Do not clamp rotationally symmetrical work-
pieces, or do so only after contacting the manu-
facturer.



Never remove balancing screws and weights at-
tached to the product.

3.4 Speed

The product is authorized for rotational operation.

The maximum speed is written on the product [maximum
speed, see »General information« chapter].

DANGER

Serious injuries caused by projectile parts ejected
when the product is used improperly!



Always pay attention to media feed lines when ro-
tating the product.



When using the side ports, the product must not
ever rotate.

DANGER

Serious injuries caused by parts being ejected
centrifugally due to a non-compliant combination
of several products!



From all of the maximum speeds indicated for the
combined products, always remain at the lowest
of those maximum speeds.

Содержание HYDROK

















































































































Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды

Hainbuch HYDROK, Руководство по эксплуатации

Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды