Hainbuch HYDROK Скачать руководство пользователя | Manualshive

Страница: 21 / 112

background image

HYDROK
Safety

Order h49 7144.907-333

21

CAUTION

Injuries caused by slipping on escaping media!



Ensure that media are not able to escape.



Drain the rest of the product.

NOTE

Serious damage to materials / the machine tool /
the product caused by workpieces being ejected
centrifugally if clamping is released while they are
still rotating!



Never release the clamping of the workpiece
while it is still rotating.

NOTE

Damage to materials caused by untightening the
wrong screws!



Do not open the screws secured with sealing lac-
quer.

2.7 Screws

WARNING

Serious injuries caused by radially installed
screws being ejected centrifugally if installed in-
correctly / poor handling!



Do not open the screws secured with sealing lac-
quer.



Screws  and  threaded  pins  fitted  radially  to  the
product that were bonded with adhesive need to
be  secured  again  using  a  standard,  medium-
strength  screw  adhesive  and  tightened  to  the
specified tightening torque [see nomenclature or
the  »Screw  tightening  torques«  chapter].  Before
reinstallation, clean and degrease the screw and
internal thread.



Radially mounted screws and threaded pins that
were not bonded with sealing lacquer or an adhe-
sive need to tightened back down to the specified
tightening torque [see nomenclature or the
»Screw tightening torques« chapter].



If in doubt, contact the manufacturer immediately
to determine how best to proceed.

«
...
19
20
21
22
23
...
»

Содержание HYDROK

















































































































Отзывы:

Нет отзывов

Похожие инструкции для HYDROK

Бренд: Ableconn Страницы: 15

Portico TVA Series

Бренд: Citel Страницы: 109

WAB501 - 802.11a/b Dual Band PC Card

Бренд: NETGEAR Страницы: 17

Бренд: Keysight Technologies Страницы: 24

Бренд: Abocom Страницы: 17

HandyPort-Serial HPS-120

Бренд: HandyWave Страницы: 11

Бренд: Pioneer Страницы: 17

Бренд: Sena Страницы: 38

Бренд: D Line Страницы: 37

Бренд: TRENDnet Страницы: 24

Бренд: Sun Microsystems Страницы: 20

Бренд: Plantronics Страницы: 2

SFPCI -VME SERIES

Бренд: Solflower Страницы: 56

Бренд: Tumi Страницы: 63

Бренд: 7inova Страницы: 4

Бренд: Quatech Страницы: 5

Бренд: Shure Страницы: 28

Бренд: Sparr Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды