Hainbuch HYDROK Скачать руководство пользователя

Страница: 76 / 112

HYDROK
Installation

Order h49 7144.907-333

7.7 Installation of the changing parts

Changing part variant x-times axial screw connection

A1 Fixing screws changing part variant x-times axial screw connec-

tion

Changing part variant x-times axial screw connection bayonet

B1 Fixing screws changing part variant x-times axial screw connec-

tion bayonet

The changing parts, such as the workpiece end-stop, can be
installed in different ways.

If necessary, in addition to these operating instruc-
tions, you should also read and follow the operating
instructions for the relevant changing parts.

INFORMATION

To be able to install the changing part, it may first be
necessary to remove the clamping element.

1. As described in the »Preparation of the machine for in-

stallation« chapter, prepare for the following steps.

2. Move the clamping device into release position.

INFORMATION

If necessary, the changing part is positioned. Position-
ing can for example be performed by marks, or a cy-
lindrical pin and a bore or a groove.

Содержание HYDROK

















































































































Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды

Hainbuch HYDROK, Руководство по эксплуатации

Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды