Hainbuch HYDROK Скачать руководство пользователя

Страница: 97 / 112

HYDROK
Maintenance

Order h49 7144.907-333

11 Maintenance

11.1 Maintenance safety

WARNING

Serious injuries caused by parts being ejected
centrifugally after a loss of clamping power!



Maintain the maintenance and cleaning intervals
of the product at all times.



It is essential to check the maintenance status of
the product at regular intervals with a structural
clamping force measurement.

CAUTION

Health risks caused by incorrect handling of
cleaning agents!



Pay attention to hazard specifications and the
safety data sheet of the manufacturer.

INFORMATION

If necessary, use any forcing / extraction threads in
the components of the product, changing parts or
clamping elements.

11.2 Maintenance schedule

The following sections describe the maintenance work
needed to ensure optimum and fault-free operation.

If increased levels of wear are detected during regular
checks, shorten the maintenance intervals to reflect the ac-
tual rate at which signs of wear appear.

Contact the manufacturer for questions relating to mainte-
nance work and maintenance intervals [see »Contact« chap-
ter].

Interval

Maintenance work

daily

Visual inspection of clamping and mating surfaces for signs of
wear, nicks and cracks [see »Visual inspection« chapter]

Visual inspection of rubber on clamping element for signs of
wear, nicks and cracks [see »Visual inspection« chapter]

Complete cleaning if heavily soiled [see »Cleaning« chapter]

Conduct a structural clamping force measurement

weekly or after 40- operat-
ing hours*

Remove the clamping element [see »Removal of the clamping
element« chapter]

Clean the clamping element, clamping taper and coupling area
[see »Cleaning« chapter]

Содержание HYDROK

















































































































Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды

Hainbuch HYDROK, Руководство по эксплуатации

Результаты поиска

Содержание HYDROK

Отзывы:

Похожие инструкции для HYDROK

Бренды по названию

Популярные бренды