Hainbuch HYDROK Скачать руководство пользователя | Manualshive

Страница: 83 / 112

background image

HYDROK
Commissioning

Order h49 7144.907-333

83

For the axial nominal total stroke, the values of axial clamp-
ing reserve and axial release stroke must be added together
[see »General information« chapter].

8.4 Tests

NOTE

Serious damage to, or destruction of, the machine
tool and the workpiece caused by damaged, in-
complete or incorrectly installed products!



Only install undamaged and complete products
properly.



If in doubt, contact the manufacturer.

Assure the following points before every installation and/or
before every time the products are put into service:



The products used are undamaged.



All fixing screws are present on the products, and are
tightened to the correct tightening torque.



None of the rubber segments on the clamping elements
and attachments are torn or exhibit porous areas.



Serrations and grooved profiles must not be excessively
rounded because this would prevent the friction coeffi-
cient from being achieved.



None of the edges and races are chipped or show any
signs of wear.



The speed set on the machine tool must not exceed the
maximum speed of the product. Always take the lowest
value of all maximum speeds for combined products in-
dicated.



Pay attention to the level of actuating force established
to enable the workpiece to be clamped with sufficient
clamping force.



Do not exceed the maximum actuating force indicated
on

the

product.

Always take the lowest value of all actuating forces indi-
cated for combined products.



All installation tools are removed from the machining
area.



Clamping device and workpiece are compatible - check
clamping diameter on a regular basis.



Conduct a clamping force measurement or pressure
test.

«
...
81
82
83
84
85
...
»

Содержание HYDROK

















































































































Отзывы:

Нет отзывов

Похожие инструкции для HYDROK

Бренд: D-Link Страницы: 18

DWL-G820 - AirPlus Xtreme G

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 46

Бренд: D-Link Страницы: 24

Бренд: NI Страницы: 11

SETU ATA211 SIP-FXS-FXO

Бренд: Matrix Страницы: 178

Бренд: Kvaser Страницы: 24

Бренд: Miele Страницы: 148

Бренд: D-Link Страницы: 40

Бренд: WELLTECH Страницы: 3

Бренд: Toa Страницы: 1

Бренд: Improved Racing Страницы: 12

Бренд: EUCHNER Страницы: 34

Бренд: Belkin Страницы: 15

Бренд: Belkin Страницы: 30

Бренд: Sonnet Страницы: 4

Бренд: Sevenoak Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды