Guardian SCC 25 Скачать руководство пользователя страница 6

Страница: 6 / 79

Page 6

GUARDIAN SCC-40

Issue (Auto VI) & V3.6t 07/12/00

CONFIGURE UNIT MODEL, SYSTEM No & ADDRESS

Enter Passcode

Before any permanent change of controller settings are made then the correct entry of the
appropriate passcode is necessary.

The settings available for change on each passcode are as follows;

Passcode

Passcode level 1

setpoints, low & high alarm settings

Passcode level 2

low & high trip settings and all level 1

Passcode level 3

system settings and levels 1 & 2

Enter passcode 15

DISCHARGE

FILTER

“

view

”

= “SETPOINT”

“

” “

”

pASS codE

DISCHARGE

FILTER

DISCHARGE

FILTER

==-= ==12

“

@:@

raise

”

==-=

==15

“

”

Press “

view

” to select “

SETPOINT

”, then press the “

next

” button twice to enter

the passcode settings.
Press “

raise

” repeatedly until passcode

is selected and then press “

accept

”

Select Unit Model

Enter Passcode as button sequence above.

“

@:@

view

”

= “SYSTEM”

SUCTION

OIL

“

@:@

type

”

= “SAFETY TRIPS”

==sE

tUP=

DISCHARGE

FILTER

====

=yEs

“

”

DISCHARGE

FILTER

DISCHARGE

FILTER

====

Unit

“

”

====

SC30

“

@:@

raise

”

DISCHARGE

FILTER

====

SC40

“

”

Press

‘view’

repeatedly until

‘SYSTEM’

is selected.

Press

‘type’

repeatedly until

‘SAFETY TRIPS’

is selected. Press

‘accept’

‘Unit’

is displayed press

‘accept’

Display shows unit model currently selected which may be wrong.

Press

‘raise’

repeatedly until correct model is displayed (e.g.SC30) and then press

‘accept’

which causes the display to wink briefly and display the new unit model selection
(e.g SC40 )

Содержание SCC 25
















































































Результаты поиска

Содержание SCC 25

Отзывы:

Guardian SCC 25, Руководство пользователя, Страница: 6 / 79

Результаты поиска

Содержание SCC 25

Отзывы: