manualshive.com logo in svg

Guardian SCC 25, Руководство пользователя, Страница: 53 / 79

Поделиться
Скачать
Guardian SCC 25 Скачать руководство пользователя страница 53

                                                                                                                                       Page 53

GUARDIAN SCC-40

Issue (Auto VI) & V3.6t 07/12/00

TIMER SETPOINTS

Timer delays are displayed in the windows detailed below with selections
 'type'= 'TIMERS and 'view'= 'LATEST VALUE'.
 All timer delays count down to zero in tenths of a minute :-
Timers are adjusted  using 'raise', 'lower', 'next', 'accept' when  'view'= setpoints

Adjustable timers are available for:-

Timer

Window

Range and description

Stage-Up      (u)

SUCTION

0.5 to 12min

Time Compressor at 100% before
allowing next compressor to start.

Stage-Down (d)

DISCHARGE

0.5 to 10min

Time compressor at minimum load or
time at 50% if in slide balance mode
before stopping.

Set at 10.0 min = none,

NO STOP AT MINIMUM,

 MANUAL STOP ONLY

N.B. To exit

 none

 setting =

Discharge, Timer, Setpoint, Lower, Accept.

Pre-Lubrication
                     (p)

OIL

0.0 to 5.0min

Oil pump run before compressor starts.
At-minimum signal  must  be present at
the end of this timer or a  'S-UP' trip is
displayed before the  motor is started.
On a siphon system this timer is
restarted with the motor and inhibits
LOW oil differential pressure  alarms and
trips whilst it is still active.

Pump-off-after
Stop             (o)

FILTER

0.0 to 5.0min

Oil pump run delay after  compressor
stops until at-minimum received.

Capacity load
delay

CAPACITY%

0.5 to 5.0min

This  timer determines the interval
between loading/unload pulses when the
control is close to ( <0.3  bar) the control
setpoint. This delay is also used after
starting motor before loading pulses
are started.

After-Stop

LOAD %

1.0 to 5.0min

the minimum time required after stop
before allowing another restart.

Содержание SCC 25
















































































Отзывы:

Нет отзывов