manualshive.com logo in svg

Guardian SCC 25, Руководство пользователя, Страница: 38 / 79

Поделиться
Скачать
Guardian SCC 25 Скачать руководство пользователя страница 38

                                                                                                                                       Page 38

GUARDIAN SCC-40

Issue (Auto VI) & V3.6t 07/12/00

STARTING

After a start request has been made the Oil pump is started. Provided a pump
running signal has been received, the oil differential limit is satisfied,(within the oil
differential delay time ‘dt’), and the slide is at minimum the motor will then start.
     If the slide is not at minimum when the pump is started then the following
procedure is completed:-
1.  The un-load solenoid is energised.
2.  If the slide returns to minimum within the differential delay  time,’dt’, then motor

start will proceed as above.

3.  When the slide does not return to minimum within ‘dt’ the pump continues to run

until the slide is at minimum or the pump pre-lube delay is exceeded.

4.  If the slide is at minimum then the pump is stopped and a motor re-start delay

time is enforced before a normal starting procedure is attempted. This allows
excess oil in the compressor to drain away.

5.  If the slide has not made minimum after the pre-lube delay the compressor will

go to the tripped state 

'S-uP'/'trip'.

6.  If the pump run signal is not present within ‘dt’ the compressor goes to the

tripped state 

'PunP'/'trip'

If the motor running signal,(motor in delta), is not received within thirty seconds the
compressor will go to  the  tripped state 

'nnot'/'trip'.

Содержание SCC 25
















































































Отзывы:

Нет отзывов