manualshive.com logo in svg

Guardian SCC 25, Руководство пользователя, Страница: 23 / 79

Поделиться
Скачать
Guardian SCC 25 Скачать руководство пользователя страница 23

                                                                                                                                       Page 23

GUARDIAN SCC-40

Issue (Auto VI) & V3.6t 07/12/00

CONTROL STATUS LED LAMPS

WAITING

The  compressor is stopped and is waiting timeout of time-between-starts delay or
time-after-stop delay or the oil sump temperature is LOW or the discharge temperature is
HIGH or the external refrigeration inhibit signal is present in 'AUTOMATIC' mode.

READY

The compressor is stopped and ready to start and has not been tripped. This state is
displayed after the compressor has stopped after reaching low-trip suction limit which is
considered as a stop and resets automatically.

STARTING

The  compressor is running and has received oil pump and compressor running signals but
may have other alarms which require action.

RUNNING

The compressor is running  and has received oil pump and compressor running signals but
may have other alarms which require action.

LOADING

The solenoid loading valve is being pulsed opened to increase the slide capacity.

UNLOADING

The solenoid unloading valve is being pulsed opened to decrease the slide capacity.

AT MINIMUM

The slide is below minimum value (25%) or the external minimum setting limit switch is
closed.

AT MAXIMUM

The slide is above maximum value (95%) or the  external maximum setting limit switch is
closed.
This lamp is lit when 'back-off' unloading is in progress due to over-current, discharge
pressure or capacity .

LED LAMPS.

Compressor
control status

Used to display compressor control status

TRIPPED

Flashing RED compressor tripped indicator

MANUAL

Mode selections:   OFF, COMPRESSOR, CAPACITY

AUTOMATIC

Mode selections:   LOCAL, REMOTE

‘type’

7 led lamps. Selection for 4-digit LED displays
PRESSURE, TEMPERATURE, EQUIVALENT TEMPERATURE
DIFFERENTIALS, HOURS RUN, TIMERS & SAFETY TRIPS

‘view’

7 led lamps. Selection for 4-digit LED displays
LATEST VALUE, SETPOINT, LOW ALARM,
HIGH ALARM, LOW TRIP, HIGH TRIP & SYSTEM

Содержание SCC 25
















































































Отзывы:

Нет отзывов