GTO 3000XLS Скачать руководство пользователя страница 36

Страница: 36 / 44

LPA 3000XLS/3200XLS Instruction Manual

Push-To-Open Installation Information

Swinging gates shall not open into public access areas!
A “Push-to-Open” gate opens out from the property (operator arm extends to open the gate). A Push-To-

Open installation requires the purchase of a Push-To-Open Bracket

[R4388].

In a Push-To-Open installation the operator is installed while the gate is in the CLOSED POSITION.

Install the Operator

Follow directions for installing the 3000XLS

beginning on page 7.

The Push-To-Open

installation differs from the Pull-To-Open

installation in the following ways

1. In a Push-To-Open installation, the arm

fully extends to open the gate, and it fully

retracts to close the gate. (C)

2. You will install the operator while the gate

is in the CLOSED POSITION (arm fully

retracted). (A)

3. You must use the Push-to-Open Post Pivot

Bracket

[R4388] in the Post Bracket assembly. (B)

4. IMPORTANT: While determining the mounting point for the

post pivot bracket assembly be sure that the position allows

for 2” clearance between the gate and the operator in both the

open and closed positions (see diagram below). This clearance

will give the operator the most efficient leverage point for

opening and closing the gate and more importantly provides

the least possible pinch area. (C)

Level Operator

Fence Post

Clevis Pin, Bushing, and Hairpin Clip

Gate In Closed Position

Push-To-Open

Post Pivot Bracket

[R4388]

3/8" x 3" Bolt

Post Bracket

3/8" Nut

3/8" Lock Washer

3/8" Washer

Gate in the Open Position

Pinch Area

2" minimum

Gate in the Closed Position

Pinch Area

2" minimum

Clamp

MAX

Install the 3200XLS Operator

Now install the SECOND gate

operator on the SECOND gate

in the same manner.

24/7 Troubleshooting Wizard: http://

support.gtoinc.com

The Troubleshooting Wizard has

detailed information on Push-To-Open

Installations.

Содержание 3000XLS













































Результаты поиска

Содержание 3000XLS

Отзывы:

Похожие инструкции для 3000XLS

Бренды по названию

Популярные бренды

GTO 3000XLS, Руководство по установке

Результаты поиска

Содержание 3000XLS

Отзывы:

Похожие инструкции для 3000XLS

Бренды по названию

Популярные бренды