GTO 3000XLS Скачать руководство пользователя страница 40

Страница: 40 / 44

LPA 3000XLS/3200XLS Instruction Manual

Generation 3 Visual Feedback

SYMPTOM

DIAGNOSIS

CHECK:

Status (clear)1 blink Cycle Terminal

Shorted

• Disconnect the push button, keypad, intercom keypad, or

any other accessory wired to this terminal.

• Try the remote. If the remote works, then the problem is

the accessory.

Status (clear) 2

blinks

Safety Terminal

Shorted

• Disconnect the loop detector, photo beam, or any other

accessory wired to this terminal.

• Try the remote. If the remote works, the problem is the

accessory.

Status (clear) 3

blinks

Exit Terminal

Shorted

• Disconnect exit wand, loop detector, photo beam, or any

other accessory wired to this terminal.

• Try remote. If the remote works, the problem is the

accessory.

Status (clear) 4

blinks

Shadow Terminal

Shorted

• Disconnect the loop detector, photo beam, or any other

accessory wired to this terminal.

• Try remote. If the remote works, the problem is the

accessory.

Status (clear) 5

blinks

Close Edge

Terminal Shorted

• Disconnect the edge sensor, photo beam, or any other

accessory wired to this terminal.

• Try the remote. If the remote works, the problem is the

accessory.

Status (clear) 6

blinks

Open Edge

Terminal Shorted

• Disconnect edge sensor, photo beam, or any other

accessory wired to this terminal.

• Try the remote. If the remote works, the problem is the

accessory.

RF (yellow) Flickers Receiving 318 MHz

• Normal operation when remote or wireless keypad is used.

RF (yellow)OFF

No 318 MHz RF

Received

• Battery in Remote

• Program Remote

• Antenna Receiver Connections

• Antenna Receiver

Power (green)
ON

AC or Solar Power

Present

• Normal Operation

VOLTAGE READINGS

18 Vac Transformer

18.0 to 22.0 Vac

10 W Solar panel (single)

18.0 to 22.0 Vdc

In FULL SUN

— measure voltage with the Solar Panel Disconnected.

12 V, 7 amp hour Battery

12.5 to 13.5 Vdc

or Two 12V, 7 amp hour Batteries if using solar power

Measure voltage at battery terminals with battery disconnected

Charging circuit

12.0 to 14.8 Vdc

Measure voltage at battery terminals with battery connected

Содержание 3000XLS













































Результаты поиска

Содержание 3000XLS

Отзывы:

Похожие инструкции для 3000XLS

Бренды по названию

Популярные бренды

GTO 3000XLS, Руководство по установке

Результаты поиска

Содержание 3000XLS

Отзывы:

Похожие инструкции для 3000XLS

Бренды по названию

Популярные бренды