GTO 3000XLS Скачать руководство пользователя страница 30

Страница: 30 / 44

LPA 3000XLS/3200XLS Instruction Manual

Step 4

Press the transmitter to open

the gates. Gates will OPEN fully.

The gate in step 3A or 3B is now

programmed.

Gates in

OPEN

Postion

Control

Box

Master

Gate

Operator

Second

Gate

Operator

Step 5

Press the transmitter to activate

operator arms. The gates will

begin to CLOSE.

Gates

Closing

Control

Box

Master

Gate

Operator

Second

Gate

Operator

Step 6

The gate that was programmed in step 4

will stop on its own. Press the transmitter

again to stop the other gate when it

reaches the desired CLOSED limit.
A1. Master gate reaches closed postion. -

press and hold LEARN MAST LIMIT for

5 seconds, or until buzzer beeps to set

closed postion.

(Master gate is now programmed)

B1. 2nd gate reaches closed postion -

press and hold LEARN 2ND LIMIT for 5

seconds, or until buzzer beeps to set

closed postion.

(Second gate is now programmed)

Control

Box

Learn Master

Limit Button

1 2 3 4

DIP

STATUS

LEARN RMT

LEARN

MAST LIMIT

LEARN

2ND LIMIT

SOFT START OFF
WARNING OFF
OPEN PULL
SLV OPEN DLY.
MODE1 OFF
MODE2 OFF

ON
ON
PUSH
SIMULT.
ON
ON

120 MIN

MAX

AUTO CLOSE TIME

STALL FORCE

Learn 2ND

Limit Button

Learn Master

Limit Button

1 2 3 4

DIP

STATUS

LEARN RMT

LEARN

MAST LIMIT

LEARN

2ND LIMIT

SOFT START OFF
WARNING OFF
OPEN PULL
SLV OPEN DLY.
MODE1 OFF
MODE2 OFF

ON
ON
PUSH
SIMULT.
ON
ON

120 MIN

MAX

AUTO CLOSE TIME

STALL FORCE

Learn 2ND

Limit Button

Gates in Closed

Position

Step 7

Press the transmitter once again to OPEN

gates.
Both gates closed position are

now programmed.
If you make a mistake and set

the limit at the wrong position:

press your transmitter to return

the gate to the fully opened

position, then press and hold the LEARN MAST LIMIT and/or the LEARN 2ND LIMIT

button for 5 seconds. This will clear the memory for the closed limit position.

Repeat Steps 1-6.

Gates in

OPEN

Postion

Control

Box

Master

Gate

Operator

Second

Gate

Operator

Содержание 3000XLS













































Результаты поиска

Содержание 3000XLS

Отзывы:

Похожие инструкции для 3000XLS

Бренды по названию

Популярные бренды

GTO 3000XLS, Руководство по установке

Результаты поиска

Содержание 3000XLS

Отзывы:

Похожие инструкции для 3000XLS

Бренды по названию

Популярные бренды