GTO 3000XLS Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 44

background image

viii

LPA 3000XLS/3200XLS Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

!

Warning signs (4 enclosed) to be installed on each side

of the gate (3–5 feet above the bottom of the gate).

Product identification and manual operation instruction

label (1) installed on control box.

Logo and warning labels (2) installed on each side of master operator housing.

Logo and warning labels (2) installed on each side of second operator housing.

Conforms to UL STD 325

Certified to CSA STD C22.2 No.247

Maximum Gate: 650 lb. (294.8 kg); 16 ft. (4.9 m)

Voltage: 12 Vdc; Frequency: 0 Hz; Power: 60 W

Class I & II Vehicular Swing Gate Operator.

3000XLS SERIES DC Swing Gate Operator

P/N LPA-3000XLS

9901178

TO MANUALLY OPEN AND CLOSE THE GATE:

1. Turn control box power switch OFF.

2. Disconnect front or rear mount from mounting bracket.

3. Pull operator away from mounting brackets and move gate.

Disconnect operator ONLY when the control box power

switch is OFF and the gate is NOT moving.

Serial Number:

LPA3000XLS-0000000

MMDDYY

GTO Access Systems, LLC - Tallahassee, Florida USA

«
...
8
9
10
11
12
...
»

Содержание 3000XLS













































Отзывы:

Нет отзывов

Похожие инструкции для 3000XLS

Бренд: FAAC Страницы: 25

Бренд: FAAC Страницы: 15

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 30

Бренд: Kenner Страницы: 13

Бренд: LockMaster Страницы: 2

Бренд: RIB Страницы: 56

Бренд: RIB Страницы: 48

Бренд: Entre Matic Страницы: 48

Бренд: OZ Trends Страницы: 21

Бренд: BelFox Страницы: 14

Бренд: BelFox Страницы: 34

Бренд: Polaris Страницы: 187

Бренд: V2 Страницы: 15

Бренд: Chamberlain Страницы: 96

Бренд: CAME Страницы: 40

Бренд: CAB Страницы: 32

Бренд: Sky Way Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды