GTE ADICOS HOTSPOT-1000 Скачать руководство пользователя страница 28

Страница: 28 / 36

OPERATION

ADICOS HOTSPOT-1000

410-2410-001 EN12

7 Operation

During operation, the ADICOS HOTSPOT-1000 monitors the area within its field of view and

triggers an alarm when the limits are exceeded. The scan interval is 100 milliseconds.

7.1 Software Access

When an ADICOS M-BUSMASTER is used, detailed information on the detector can be ac-

cessed via the M-Bus. To be able to gain the detector information, you will need a PC with

installed ADICOS service software and that is connected to the ADICOS M-Bus interface.

The communication number (COM or K.N.) shown on the ID plate and on the front of the de-

tector is used to access detailed information on the detector in the software. Parameterization

of the ADICOS HOTSPOT-1000 is also done in the software. However, only properly trained

personnel may perform this task. And in the software you can also look at the current thermal

image of the detector, enabling potential sources of ignition to be revealed.

7.2 Alarm

If the temperature limits sets in the ADICOS HOTSPOT-1000 are exceeded, the ADICOS

HOTSPOT-1000 triggers an alarm. The internal alarm relay is engaged and the red LED lights

up. The status is also transmitted via the M-Bus.

If an alarm delay has been set, the alarm is not triggered until the alarm conditions have been

met for longer than the set duration.

7.2.1

Fire Detection System Operation

If the ADICOS HOTSPOT-1000 is connected to a fire panel, the alarm is transmitted to the fire

panel via the fire detection system module. The fire detection system triggers the ADICOS

HOTSPOT-1000 alarm. The alarm relay is triggered and the red signal LED lights up. In case fire

panel does not recognize to the alarm condition and does not responds the red LED flashes.

7.2.2

Resetting Alarm

The ADICOS HOTSPOT-1000 remains in a state of alarm until the temperatures fall below the

set limits again. Scans occur at 100 millisecond intervals to determine whether the tempera-

tures have fallen below the limits. When the temperatures have fallen below the alarm limits

and the alarm conditions are no longer met, the alarm state is automatically canceled and the

alarm relay stops operation. If an alarm duration time has been set, the signal LED “Alarm” is

not reset until after a respective delay.

If the alarm LED is controlled by a fire detection system, the alarm state can be reset with the

alarm reset contact on the fire detection system.

7.2.3

Alarm Duration

The alarm duration is a parameter that can optionally be set via the ADICOS service software.

The purpose of the alarm duration is to ensure that, once the alarm conditions are no longer

met, the signal LED “Alarm” is not reset unit after a respective delay. The default alarm duration

is 7.5 minutes.

Содержание ADICOS HOTSPOT-1000





































Результаты поиска

Содержание ADICOS HOTSPOT-1000

Отзывы:

Похожие инструкции для ADICOS HOTSPOT-1000

Бренды по названию

Популярные бренды

GTE ADICOS HOTSPOT-1000, Руководство по эксплуатации

Результаты поиска

Содержание ADICOS HOTSPOT-1000

Отзывы:

Похожие инструкции для ADICOS HOTSPOT-1000

Бренды по названию

Популярные бренды