GST I-9105R Скачать руководство пользователя страница 25

Страница: 25 / 26

I-9105R
Intelligent Reflective Beam Detector
Installation and Operation Manual

The Intelligent Solution

codes and laws. Take specific maintenance measures on the basis of

different environments.

The smoke detector contains electronic parts. Even though it’s made to

last for a long period of time, any of these parts could fail at any time.

Therefore, test your smoke detector at least every half-year according

to national codes or laws. Any smoke detectors, fire alarm devices or

any other components of the system must be repaired or replaced as

long as they fail.

Appendix 2 Warranty

GST

warrants that the product will be free from defects in design,

materials and workmanship during the warranty period. This warranty

shall not apply to any product that is found to have been improperly

installed or used in any way not in accordance with the instructions

supplied with the product. Anybody, including the agents, distributors or

employees, is not in the position to amend the contents of this warranty.

Please contact your local distributor for products not covered by this

warranty.

Содержание I-9105R



























Результаты поиска

Содержание I-9105R

Отзывы:

Похожие инструкции для I-9105R

Бренды по названию

Популярные бренды

GST I-9105R, Инструкция по установке и эксплуатации

Результаты поиска

Содержание I-9105R

Отзывы:

Похожие инструкции для I-9105R

Бренды по названию

Популярные бренды