Grundig GHP-MM08 страница 79 Скачать руководство пользователя | Manualshive

Страница: 79 / 83

background image

79 / EN

Heat Pump Monobloc Inverter / User Manual

77 Heat Pump Space Heater 202202

4.4.26 E22 E32 E33 E35 E37 E38 analysis

These codes mean the controller is performing some kind of specific action; they are neither
error nor failure.

!

E22 will occur if the inverter module is resetting.

!

E32 E33 and E35 will occur if the inverter module is debugging the data.

!

E37 will occur if the compressor frequency is limited because of the input current of the
inverter module.

!

E38 will occur if the compressor frequency is limited because of the input voltage of the
inverter module.

4.4.27 E01/E02/E03/E04/E05/E06/E07/ E08/E09/E10/E14/E28 analysis

Before starting heat pump, if the communication cables with two cores (A and B) between the
control board 1 and the control board 2 are not connected, all these errors above will occur on
the user interface and don’t start heat pump. First of all, you must confirm that the
communication cables (A and B) between these two control boards have been connected
correctly to start heat pump.

E01/E02/E03/E04/E05/E06/E07/

E08/E09/E10/E14/E28

Connect the communication cables between the

control board 1 and the control board 2

«
...
77
78
79
80
81
...
»

Содержание GHP-MM08




















































































Отзывы:

Нет отзывов

Похожие инструкции для GHP-MM08

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 2

Бренд: µ-Dimension Страницы: 6

OmniConverter GPoE+/S

Бренд: OST Страницы: 10

AVerCaster HD Duet

Бренд: Avermedia Страницы: 4

Бренд: Lampizator Страницы: 32

Бренд: Wacker Neuson Страницы: 36

OBID i-scan ID ISC.ANT.PS-A

Бренд: Feig Electronic Страницы: 28

Бренд: ADF Web Страницы: 25

Бренд: Kramer Страницы: 30

Бренд: Love Controls Страницы: 2

PerfectPower PP150

Бренд: Waeco Страницы: 44

Бренд: Digi Страницы: 6

Бренд: Salicru Страницы: 144

Бренд: TRENDnet Страницы: 1

Бренд: Mayty Страницы: 14

USB-4600 Series

Бренд: Advantech Страницы: 26

Бренд: Transition Networks Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды