manualshive.com logo in svg

Grizzly G0677, Руководство пользователя

Владелец Ручной G0677 - мощный инструмент для работы с древесиной. Вы можете легко найти и скачать бесплатное Руководство пользователя с manualshive.com. Это руководство поможет вам освоить все функции и возможности этого прекрасного инструмента. Не упустите шанс загрузить его прямо сейчас!

Поделиться
Скачать
background image

G0677 24" Planer/Sander

-5-

The information contained herein is deemed accurate as of 7/15/2019 and represents our most recent product specifications.

Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.

PAGE 1 OF 3

Model G0677

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL G0677 24" 15 HP 3‐PHASE PLANER/WIDE‐BELT

SANDER

Product Dimensions:

Weight............................................................................................................................................................ 2314 lbs.

Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 61 x 44-1/2 x 68 in.

Footprint (Length x Width)..................................................................................................................... 42-1/2 x 31 in.

Shipping Dimensions:

Type................................................................................................................................................... Wood Slat Crate

Content........................................................................................................................................................... Machine

Weight............................................................................................................................................................ 2626 lbs.

Length x Width x Height....................................................................................................................... 63 x 47 x 76 in.

Must Ship Upright................................................................................................................................................... Yes

Electrical:

Power Requirement..................................................................................................... 220V or 440V, 3-Phase, 60 Hz

Prewired Voltage.................................................................................................................................................. 220V

Full-Load Current Rating............................................................................................... 40.6A at 220V, 20.3A at 440V

Minimum Circuit Size.......................................................................................................... 50A at 220V, 30A at 440V

Connection Type........................................................................................... Permanent (Hardwire to Shutoff Switch)

Switch Type............................................................................................ Control Panel w/Magnetic Switch Protection

Voltage Conversion Kit................................................................................................................ P06778134 for 440V

Recommended Phase Converter....................................................................................................................... H3741

Motors:

Main

Horsepower.............................................................................................................................................. 15 HP

Phase.................................................................................................................................................... 3-Phase

Amps..................................................................................................................................................... 36A/18A

Speed................................................................................................................................................ 3450 RPM

Type........................................................................................................................................... TEFC Induction

Power Transfer ............................................................................................................................... V-Belt Drive

Bearings........................................................................................................ Sealed & Permanently Lubricated

Centrifugal Switch/Contacts Type................................................................................................................ N/A

Table Elevation

Horsepower............................................................................................................................................. 1/4 HP

Phase.................................................................................................................................................... 3-Phase

Amps................................................................................................................................................... 1.2A/0.6A

Speed................................................................................................................................................ 1725 RPM

Type........................................................................................................................................... TEFC Induction

Power Transfer ............................................................................................................................... V-Belt Drive

Bearings........................................................................................................ Sealed & Permanently Lubricated

Centrifugal Switch/Contacts Type................................................................................................................ N/A

Machine Data Sheet

Содержание G0677

































































































Отзывы:

Нет отзывов

Похожие инструкции для G0677

XINDAK C06 Instructions Manual preview
C06
Бренд: XINDAK Страницы: 13
NAD S500i Owner'S Manual preview
S500i
Бренд: NAD Страницы: 32
NAD M5 C/AH Owner'S Manual preview
M5 C/AH
Бренд: NAD Страницы: 18
NAD C541i Service Manual preview
C541i
Бренд: NAD Страницы: 37
NAD C540 Owner'S Manual preview
C540
Бренд: NAD Страницы: 38
NAD C521 Owner'S Manual preview
C521
Бренд: NAD Страницы: 44
NAD C 542 Owner'S Manual preview
C 542
Бренд: NAD Страницы: 44
NAD C 525BEE Owner'S Manual preview
C 525BEE
Бренд: NAD Страницы: 50
NAD C 521BEE Owner'S Manual preview
C 521BEE
Бренд: NAD Страницы: 50
NAD 523 Owner'S Manual preview
523
Бренд: NAD Страницы: 52
Panasonic SLMP50 - PORT. CD PLAYER Operating Instructions Manual preview
SLMP50 - PORT. CD PLAYER
Бренд: Panasonic Страницы: 8
Grizzly G0550 Instruction Manual preview
G0550
Бренд: Grizzly Страницы: 56
Alesis MASTERLINK ML-9600 Reference Manual preview
MASTERLINK ML-9600
Бренд: Alesis Страницы: 59
Lakeshore JJ665 Manual preview
JJ665
Бренд: Lakeshore Страницы: 12
Tascam CD-A630 Owner'S Manual preview
CD-A630
Бренд: Tascam Страницы: 76
Emerson Cd Cruiser CKD9907 Owner'S Manual preview
Cd Cruiser CKD9907
Бренд: Emerson Страницы: 17
Samsung Z-850 Owner'S Instructions Manual preview
Z-850
Бренд: Samsung Страницы: 16
Samsung yePP MCD-SM85 User Manual preview
yePP MCD-SM85
Бренд: Samsung Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды