Grizzly G0677 Скачать руководство пользователя

Страница: 53 / 96

G0677 24" Planer/Sander

-51-

Adjusting Sanding Drum V-Belts

1. DISCONNECT THE PLANER/SANDER

FROM THE POWER SOURCE!

2. Loosen the lock nuts on the idler pulley

adjustment bracket (see

Figure 69).

Figure 69. Sanding drum V-belt adjustment

locations.

3. Turn the long hex bolt to adjust the V-belt ten-

sion until the belts deflect

⁄

" off of center

when pushed with your finger, as shown in

Figure 67.

4. Retighten the lock nuts.

Figure 67. Correct V-belt deflection.

Pulley

Deflection

Pulley

Turn the adjustment nut up or down until

the V-belts deflect

⁄

" off of center when

pushed hard with your finger, as shown in

Figure 67.

4. Retighten the lock nut.

Idler Pulley
Adjustment

Bracket

Hex Bolt

Sanding Drum

V-Belts

Lock Nuts

Adjusting Cutterhead & Idler
V-Belts

1. DISCONNECT THE PLANER/SANDER

FROM THE POWER SOURCE!

2. Loosen the lock nuts on the tension bolt (see

Figure

3. Turn the wing nut until the V-belts deflect

" off of center when pushed with your

finger, as shown in

Figure 67.

Figure 68 Tension bolt wing nut .

⁄

4. Retighten the lock nuts.

Wing Nut &

Flat Washer

Tension

Bolt

Lock Nuts

Содержание G0677

































































































Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды

Grizzly G0677, Руководство пользователя

Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды