Grizzly G0677 Скачать руководство пользователя страница 57

Страница: 57 / 96

G0677 24" Planer/Sander

-55-

7. Insert two 2x4 x 8' wooden studs under the

table to support the table, and then (with
help) lift the table slightly and move it out of
the rear of the machine.

8. Disconnect the limit switch, remove all mount-

ing screws, and remove the emergency stop
plate assembly.

9. Turn both tracking adjustment bolts counter-

clockwise five turns, remove one roller sup-
port, and slide the drum out of the table
assembly.

10. Remove the old feed belt, inspect rollers,

bearings, and table for wear and replace as
required.

11. Install the new feed belt. Note: The belt is

non-directional.

12. Install the front roller, the roller support,

and  turn  both  tracking  adjustment  bolts
clockwise  equally  so  the  feed  belt  becomes
taught  and  does  not  hang  loose.  DO  NOT
OVERTIGHTEN the belt.

13. With a helper, install the table from the rear in

a similar fashion as it was removed.

14. Install the table guides and the left and right

lower access panels/doors.

15. Align the leadscrew flanges with the marks

made in

Step 6, and install the hex bolts.

16. Install the table height limit switches (refer to

Page 42

)

17. With a helper, install the gear box, vibration

dampener washers, and mounting bracket.

18. Install the emergency stop plate assembly

and the limit switch.

19. Start the conveyor motor and turn the con-

veyor tracking bolts as required until the feed
belt tracks straight without loading up on one
side of the table.

Feed Belt

Replacement

Replace the feed belt if it becomes damaged or
you are not able to adjust belt tracking due to
wear, using the instructions on

Page 57.

Tools Needed:

Qty

Make sure that you have a lifting device or anoth-
er person to help in table removal.

Hex Wrench 10mm ........................................... 1

Combination Wrench 19mm ............................. 1

Combination Wrench 12mm ............................. 1

Combination Wrench 14mm .............................. 1

Phillips Screwdriver #2 ..................................... 1

8' 2x4s

.............................................................. 2

Permanent Marker

............................................ 1

Lifting Assistants ............................... As Needed

To remove the feed belt, use Figure 76 and
match the number with the steps below:

1. Adjust the table so the feed belt is approxi-

mately two-inches away from the sanding
roller, then

DISCONNECT THE PLANER/

SANDER FROM THE POWER SOURCE!

2. Remove the gear box mounting bracket, and

with an assistant's help, slide the motor and
gear box from the roller shaft and lower it to
the floor.

Note: Do not loosen the two vibra-

tion dampener washers shown in

Figure 76.

3. Remove the two table height limit switches.

4. Remove both lower access panels/doors.

5. Remove the left and right table guides.

6. Using a permanent marker, mark all four

leadscrew flange positions (

Figure 75), and

remove all bolts from the flanges. Try not to
turn the flanges during the following steps.

Figure 75. Marking leadscrew for reassembly.

Timing Mark

Содержание G0677

































































































Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды

Grizzly G0677, Руководство пользователя

Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды