Grizzly G0677 Скачать руководство пользователя страница 59

Страница: 59 / 96

G0677 24" Planer/Sander

-57-

Feed Belt Tension

The  feed  belt  tension  has  been  adjusted  at  the
factory  and  should  require  no  further  attention.
However, adjust the feed belt tension if  you notice
that  your  feed  belt  is  slipping  or  is  tracking  off
center.

Tools Needed:

Qty

Wrench or Socket 10mm ....................................1
Phillips Screwdriver #2 .......................................1

DO NOT sand boards with the guard removed.

Failure to follow this warning could result in

serious personal injury.

Figure 77. Feed belt tension adjustment bolts.

Note: Safety guard removed only for clarity.

Safety Guard

Feed Belt

Adjustment

Bolt

Adjustment Bolt

4. When tensioned properly you should not be

able to lift the feed belt off of the table surface
or slide it back and forth.

To adjust the feed belt tension:

1. DISCONNECT THE PLANER/SANDER

FROM THE POWER SOURCE!

DO NOT REMOVE THE SAFETY GUARD
DURING THE FOLLOWING STEPS!

2. Find the adjustment ports

in the safety guard

(

Figure 77) at the front end of the fe

table.

3. Turn both

left and right adjustment bolts

(

Figure 77) clockwise equally t

o increase

tension.

Feed Belt Tracking

NOTICE

Adjust the feed belt tension before adjusting

the feed belt tracking.

4. Run the feed belt for 3-5 minutes and recheck

the tracking.

Repeat

Steps 2-4

until the feed belt tracking

is satisfactory.

Figure 78. Guide wheels.

Note: Safety guard removed only for clarity.

To adjust the feed belt tracking:

1. Turn the feed belt ON.

2. If the feed belt is tracking to the right side

of the table, turn the

right adjustment bolt

(

Figure 77) clockwise.

3. If the feed belt is tracking to the left side of

the table, turn the

left adjustment bolt clock-

wise.

Note: The edge of the feed belt should just

touch the guide wheels as shown in

Figure

78.

Guide Wheel

Tools Needed:

Qty

Wrench or Socket 19mm ....................................1

Содержание G0677

































































































Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды

Grizzly G0677, Руководство пользователя

Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды