Grizzly G0677 Скачать руководство пользователя страница 21

Страница: 21 / 96

G0677 24" Planer/Sander

-19-

Sanding Belt

To install the sanding belt:

1. With the machine connected to air, turn the

belt tension knob to the 9 o'clock position.

2. Remove the lock post release lever (Figure

18) by turning it counterclockwise a

⁄

turn

and pulling it up and out of the mounting
hole.

3. Remove the spacer block (Figure 18).

4. Making sure the rotation arrows on the sand-

ing belt point the same direction as those
shown in

Figure 18, install the sanding belt

by starting first on the upper roller and then
the lower roller.

Note: The sanding belt must be centered
between the limit switches, and the edge of
the sanding belt must be between the tongs
of the belt oscillation controller fork, as shown
in

Figures 18 & 19. Damage to the sanding

belt and sander will occur if the sander is
turned

ON before the sanding belt is correctly

positioned.

5. Replace the spacer block and tighten down

the lock post release lever.

With your hands clear of all moving parts,

turn the belt tension knob to the 12:00 posi-
tion to tension the belt.

—If the belt tension knob is turned to the 9:00

position, the belt will have no tension.

NOTICE

The directional arrow on the back of the

sanding belt must be pointing in a coun-

terclockwise direction during installation.

Failure to install the sanding belt correctly

could result in damage to the sanding belt

or the sander itself.

Figure 19. Sander outline (top view). Proper

position of belt between the limit switches.

Sanding Belt

(Back)

(Front)

Oscillation Controller Fork

Limit Switches

Figure 18. Components used when changing a

sanding belt.

Spacer

Block

ROTATION

Lock Post

Release Lever

Belt Centered

In Fork

Belt Tension

Knob (9 O'Clock

Position)

Содержание G0677

































































































Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды

Grizzly G0677, Руководство пользователя

Результаты поиска

Содержание G0677

Отзывы:

Похожие инструкции для G0677

Бренды по названию

Популярные бренды